[PR]カウンター
セキュリティが強化された最新機種に4号機、
いや、2・3号機時代に活躍した各社アミューズ仕様基板を
再利用して稼動させる・・・・・
不可能とも思われるミッションに果敢に挑む
その卓越した技術の全貌をご覧下さい 

魔法少女まどかマキガ(ユニバーサル)にマインズ社製MS−01基板
を再利用して稼動させるミッションです
This is the important mission to remodel the Pachislot named Masdoka Makiga to amusement specification. We used MS-01 circuit board made by Mines Corp.
この機種はDC12V仕様です
各社製アミューズ基板はパチスロ本体からDC24Vを
横取りして動いています
ほとんどのパチスロは主電源がDC24Vですから、各社、
この方法を採用しています

アミューズ仕様MS−01基板はDC12Vでも動くかもしれません

最近のパチスロはセキュリティが複雑になっていて、思わぬ
落とし穴にはまらないように
ここは、メーカー推奨のDC24Vで動かします
Mdoka Makiga is DC12V specification. MS-01 circuit board has a necessity as DC24V to move it. Almost circuit boards for Pachislot amusement specification, were made by DC24V specification because every Pachislots which has ever made were moved by DC24V. MS-01 circuit board might be moved by even DC12V. However, we worry about the unknown trouble. So we tried to move it by DC24V.
電源の確保     Securing of power supply
電源BOXを分解してAC100Vを横取りします   We dismantle the power supply BOX and get AC100V.
メインスイッチのON/OFFと連動するところを探って
パラレルで配線し、BOXの外に出します
  Find the place to synchronize with ON/OFF of the main switch.
  We wire it in parallel and guide it outside BOX
AV100V→DC24V・1Aの電源アダプターを使います   We use the AC adapter to change DC12V/1A from AC100V
出力の0Vを電源のGNDと共通にしてMS-01の24VとGNDをつなぎます
こうしておけば、メインスイッチのON/OFFに連動してアミューズ基板が立ちがります
 We connect 0V of the AC adapter and the Grand of the machine.
 The 0V will be in common with the Grand line.
リレーを利用して、MAXBETの信号を分岐します
メダルブロッカーの+−をリレーコイルに
つなぐとMAXBETの液晶演出に対応できます
  We use the relay to diverge the Maxbet line.
  We connect the plus and minus of the blocker coil to the relay to deal
  with the action of the game story.
MS-01基板のメダルセンサ出力信号とまどかマキガの信号をあわせます
まどかマキガのメダルセンサ信号↓です
  We equalize the signal of Madoka Makiga and MS-01.
   ↓ is the wave style of the Madoka Makiga
MS-01基板のメダル出力1の信号をきっかけに ↑  の波形の
信号をまどかマキガに送ればメダル投入と同じ結果が得られます
ただしMS-01のメダル出力1は ↓ こんな信号です
  If we are able to send the same wave style signal to the Madoka Makiga
   we will get the same consequence as inserting the medals.
  But medal output 1 of MS-01 is such a style ↓
  We should finish the job within 76msec because the second wave from
  MS-01 will come after 76msec
76msec後には第二波が来るので、76msec以内でまどかマキガの
メダル投入を完了しなければなりません 
そこで、プログラムを↓の様に修正します
  We should finish the job within 76msec because the second wave from
  MS-01 will come after 76msec
  So, we revise the program like this ↓
これをマイコンに書き込んで、回路に装着し、まどかマキガと
MS-01基板の間に割り込んでつなぎます
  We program this action and write it in the microcomputer
  Furthermore, we make the electric circuit, and set it.
  This circuit is connected between the Madoka Makiga and MS-01.
. .
次に小役が当った場合の処理です メダルを払い出さずに
得点として加算する仕事はMS-01基板がやってくれます
ここで、まどかマキガに「メダルが出たよ〜」って、
嘘の信号を送ってやらないと、エラーになります
まどかマキガのメダル払出信号は ↓ です
  And then we deal with winning.
  The mission to add points without paying medals will be done by MS-01.
  If the correct signal didn't go that medals were paid out exactly, machine will be error.
  The payout signal of the Madoka Makiga is this ↓.

  
MS-01基板は2つの払出センサ信号を持っていて、タイミングは違うのですが波形が一緒なので、これを使います

こうして、メダル入力信号と払出出力信号がまどかマキガとMS-01基板の間で一致したので、ミッションは終了です

アミューズ基板の払出信号が使えないときは、別途、回路を組んでプログラムを書き込んだマイコンを載せて対応します

やることは、どの機種でも、どこのアミューズ基板でも一緒です
  MS-01 has two kinds of signals for the payout.
  One of them has but same wave style in spite of different timing.
  So, we use it.
  We have gotten to be corresponded with the signals of the medal input and the
  payingbetween Madoka Makiga and MS-01.
  Our mission was finished completely.
  When we will not be able to use the signal for the payout, we will make the program
  and the electric circuit.
  It is the same with any amusement specification circuit board and any models too.